Paver sealing for Arlington homes
Paver Sealing in Arlington, FL
From Old Arlington's mid-century streets to the river blocks, call (904) 541-9860 for a free paver sealing estimate.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligation.
Fast, careful paver sealing in Arlington
Arlington homeowners can get paver sealing quoted for free, whether the pavers sit at a brick ranch, a newer infill house or a rental. The contractor cleans the surface, tops up the joint sand and applies sealer to the drive, the front walk, the patio or the pool deck. Use the form to get a free estimate, and a reply comes back inside 1 business day, usually much sooner.
Think about the brick ranch you bought for its long, low front. Years of sun and rain have left the pavers pale, the joints thin and a few corners soft. After a wash, new sand and a fresh coat, the walk and the drive look cared for again, and the front of the house matches the care inside it. To talk through what yours need, call (904) 541-9860.
The area stretches from the river blocks near Fort Caroline Road to the streets around Jacksonville University. A few pictures and an approximate size are enough for a first range. The date and the finish are your decisions, and nothing binds you. To begin, get a free estimate.
Arlington's story runs from Native American mounds dated to 5000 B.C. through river plantations to the subdivisions that followed the Mathews Bridge in 1953. Each era left different ground and different homes, which is why pavers here vary so much in age and condition. To ask about yours, call (904) 541-9860.
Why hire a local paver sealing contractor in Arlington?
Homes in Arlington run from the 1950s to today, and each one carries its own pavers and its own history of coats. Someone local can read that history on site. To talk about yours, get a free estimate.
A walk-around, free
The contractor looks over your Arlington drive, walks and patio, then writes up a number. Nothing is billed for the visit.
A range to test quotes
Companies serving Jacksonville list $1.75 to $3.25 a square foot for the full clean, sand and seal. Hold your Arlington quote against it.
Brick-friendly finishes
Matte keeps a mid-century brick front calm, and a wet look brings out patio color. You pick.
Your timeline
You choose when the work happens, what it looks like and whether it happens at all. An Arlington estimate asks for no commitment.
Get Your Free Estimate in Arlington
Tell us about your pavers in Arlington.
Free, no obligation
What paver problems show up most in Arlington?
Sand that drains away fast
Wikipedia says Regency Square Mall was built on an expanse of sand dunes, and a Metro Jacksonville history calls Arlington's higher ground unusual for North Florida, with excellent drainage. Fast-draining ground is good news for puddles. It also means joint sand can slip away in a hard rain. A good job refills the joints, then seals them in. Ask the contractor to check the joints at the lowest edge of the drive first. The Shields Mound off Fort Caroline Road shows how high some of this land sits, since observers once took it for one of the river bluffs.
Brick ranches with pavers added later
Arlingwood was developed largely in the 1950s and 1960s, with mid-century brick ranch homes on mid to larger lots. Pavers on a home that age are likely a later addition. They may sit on a base laid by someone else, so sunken spots deserve a look. Sealing over a sunken spot only preserves the dip. If nobody knows how the base was built, say so up front, and the contractor can plan for a repair. One Jacksonville company checks for settling first and repairs it before sealing everything together. Arlington drew young families from the 1940s to the 1970s, and many 1950s and 1960s houses still stand.
Street water in low pockets
A 2022 News4JAX story said Arlington Hills homeowners on Woolery Drive off Merrill Road had dealt with street flooding for at least a year. The city said stormwater there drains toward Strawberry Creek. Where water stands, grit can settle on nearby pavers. A wash clears it, and the sealing is timed for a dry stretch. If your street has had standing water, tell the contractor when you call. The city's plan there includes rebuilding the culvert that crosses under Arble Drive.
A coat nobody remembers
Renters live in about 44 percent of occupied homes in ZIP 32211. With many owners and tenants over the years, a driveway may carry a coat no one recorded. Sealer that is water-based cannot sit on top of a solvent-based coat. The contractor tests first, so the new coat can bond to what is already there. Photos help the contractor spot a film or sheen that points to an old coat.
Rust from iron-rich irrigation water
UF/IFAS says well water in most of Florida runs high in iron, and rust can show up on anything it touches. Orange stains often appear where iron-rich water irrigates a lawn. On a walkway that shows up as fans of color at the paver edge. The wash lifts it, and sealing follows once it is gone. The same marks often show up on a garage apron or a set of steps.
Do Arlingwood, Arlington Hills and the river blocks need different paver work?
Slightly, because the homes differ in age and lot. Arlingwood grew in the 1950s and 1960s, and one real estate profile finds its homes built from 1953 to 2025, with a median year of 1961. Arlington Hills sits off Merrill Road and drains toward Strawberry Creek. The same neighborhood can hold a 1953 ranch and a 2025 build, so name your street when you get a free estimate.
Old Arlington's mid-century homes carry sharp roof edges and sloping lines, according to an organization that preserves them. WJCT reports that many houses built in the 1950s and 1960s still stand. A matte finish tends to suit those straight lines. If you live on such a street, call (904) 541-9860.
Near the river, Fort Caroline Road passes the Shields Mound and the old Gilmore settlement. Jacksonville University sits on land the school bought in 1947. Wherever you live, share your cross streets when you get a free estimate so the visit is easy to plan.
Condos and townhomes are part of Arlington too, and Arlingwood alone has a share of them. Shared walks and entry courts may need a word with the association or the owner before work starts. Give the contractor that contact when you get a free estimate. It saves a second trip.
Strawberry Creek runs near Arlington Hills, and a mill dam at Red Bay and Strawberry Creek once formed the island you can still see at Tree Hill. Water has shaped this part of Arlington for a long time. If your street is near the creek, get a free estimate and say so.
Jacksonville University's campus sits in Arlington, on land the school bought in 1947. Homes near the campus date to the decades after the Mathews Bridge opened in 1953. If you live near the university, get a free estimate and mention your cross streets.
Arlingwood was established in 1941, and about 31 of its 1,139 homes change hands in a year. That means most owners stay a long time and the pavers stay with them. A long-held driveway often carries two or three coats. To ask about yours, get a free estimate.
Chaseville began after the Civil War, when Samuel Chase opened a shipyard. Farther north, the Kingsley family's Chesterfield Plantation once stood on what is now the Jacksonville University campus. Different neighborhoods grew from these starts, with different lots and soils. Name your neighborhood as you get a free estimate.
What does paver sealing cost in Arlington?
In Jacksonville, companies list $1.75 to $3.25 for every square foot cleaned, sanded and sealed. Older rentals and long-owned homes may carry a coat that needs stripping first, and that adds to the figure. Use the range to check any Arlington quote. To put a figure on these pavers, get a free estimate.
Arlingwood has mid to larger lots, so drives can run long and add square feet fast. A rental with an unknown coat may need a strip first, and sunken spots that need resetting add time. Give your rough size when you call (904) 541-9860, and the contractor can narrow the range.
Arlingwood's median sold home is about 1,616 square feet, with mid to larger lots around it. Larger lots mean longer drives, and longer drives mean more square feet to clean and seal. To see how yours measures up, get a free estimate.
| Paved area | Typical example | Clean, sand and seal |
|---|---|---|
| 300 sq ft | Small patio or walkway | $525 to $975 |
| 600 sq ft | Two car driveway | $1,050 to $1,950 |
| 1,000 sq ft | Large driveway or pool deck | $1,750 to $3,250 |
| 1,500 sq ft | Driveway plus pool deck | $2,625 to $4,875 |
Math based on the $1.75 to $3.25 per square foot that Northeast Florida paver companies published as of November 2026. Your contractor sets the actual price after seeing the surface. Repairs, leveling and stripping failed sealer are usually extra.
How does a paver sealing job work in Arlington?
Walk the lot
The contractor tours your drive, walks and patio in daylight and measures the area. Rust lines, low pockets, sunken spots and signs of an old coat are noted, along with places where gutters and downspouts drop water onto the pavers. A written number reaches you before the job is booked.
Wash and check the base
The wash lifts rust, grit and film and pulls old sand from the joints. Oil spots are treated beforehand, as one Jacksonville company describes. Sunken or lifted spots are then reset, since sealing only preserves them, and the pavers dry fully.
Refill the joints
New sand goes into every joint and is kept tight to the pavers. In fast-draining ground, full joints matter. Silica joint sand is common, and colored sand is sometimes offered as an upgrade, according to one Jacksonville company. No gaps should remain before sealing starts.
Seal in even coats
The sealer goes on in thin, even coats, worked across the whole area so the edges match the middle. Matte or wet look gets decided beforehand. Every coat goes on a dry surface, and thin coats matter more than speed.
Cure and test
Walking is fine within a few hours, and vehicles wait about a day. Furniture goes back once the surface is dry to the touch and the contractor says so. Water that beads later shows the coat is still working, and water that darkens the paver says it is time to reseal.
Complete paver services in Arlington
An Arlington paver job goes in four steps: wash, dry, re-sand, seal. The wash takes off rust, grit and film and also pulls out the old sand, so new sand follows right away. Sealer goes on last, and only onto dry pavers. To have someone look at your pavers, get a free estimate.
Long drives pick up tire marks and oil. Front walks hold leaf stain, while backyard pool decks take splash and bare feet. Since each surface calls for its own plan, the wash and the sealer may change from one part of a property to the next. Call (904) 541-9860 and tell the contractor which one matters most.
A mid-century house wants a calm finish. Matte suits clean brick lines and hides scuffs on a busy drive, but a wet look brings out patio color at the price of showing wear sooner. Many quotes put two to five years between coats, so choose a finish you will enjoy that long. To see both on a sample, get a free estimate.
Arlington's fast-draining sand helps the ground dry, though the bedding sand below a paver can stay damp after rain. Sealing waits for a dry surface. Walking is fine within hours, but vehicles stay off for roughly a day, so move them the night before. Call (904) 541-9860 to ask about the next clear window.
Questions to ask before you hire
- How long should brand new pavers sit before they get their first coat?
- Can you lift and reset the pavers that have sunk near my downspouts?
- What will you need from me that day, such as a hose, an outlet or an open gate?
- How do you clean older pavers without wearing down the surface?
- Will you rinse the sand off my driveway edges and walkways before you leave?
- Will you come look at my pavers in person before you give me a price?
- How do you deal with weeds and ant hills coming up through the joints?
What do sealed pavers look like around Arlington?
Why local matters in Arlington
Arlington homes span the 1950s to the present, so no two driveways share a history. Someone who works here asks about the last coat first, which means a sealer that fits what is already down. To get started, call (904) 541-9860.
The area covers a wide stretch of Jacksonville east of the river, from Fort Caroline Road to the Intracoastal side. A local contractor plans visits street by street instead of across town. That keeps appointment windows short. Name your cross streets as you get a free estimate.
A job depends on a dry window, so fast answers matter. The goal is a reply within a day. Call (904) 541-9860 early in the week so the forecast has room to change.
Ask how a callback works before the job starts. A nearby contractor can return for a second look at a settled corner. To raise it now, get a free estimate.
A rental or a long-held home may hide its sealing history. A contractor who works in Arlington tests the old coat before choosing a product. That testing keeps a new coat from clashing with what is already down. To start, call (904) 541-9860.
What makes Arlington different from other parts of Jacksonville?
Arlington sits east of Downtown across the St. Johns, and it joined the city in 1968. After the Mathews Bridge opened in 1953, Arlington outgrew every other part of Jacksonville for twenty years. Atlantic Boulevard, finished in 1910, was Florida's first modern improved highway. If your home sits on either road, get a free estimate and describe your drive.
Jacksonville University bought land in Arlington in 1947 and finished its first building in 1950. Tree Hill Nature Center, a city park since 1971, sits on Lone Star Road. Norman Studios, a film studio from the 1920s, is part of the area's history too. If you live near a place on this list, call (904) 541-9860.
The Dames Point Bridge, finished in 1989, links Arlington to the Northside across the St. Johns. Regency Square Mall opened in 1967 on a field of sand dunes. Parts of the land here are high and drain well. Ask a contractor what that means for your drive when you get a free estimate.
Old Arlington, Inc. offers tours of mid-century homes, and a Visit Jacksonville guide lists 12 stops to explore in the old part of Arlington. A Metro Jacksonville history traces Native American occupation here as far back as 5000 B.C. If your street runs near any of it, call (904) 541-9860.
Atlantic Boulevard, completed in 1910, started as an 18-foot-wide road that critics soon called too narrow for the traffic between the mainland and the beach. Eugene Gilbert first proposed it in the 1890s and paid for the surveys himself. Today it still runs through Arlington to the Jacksonville Beaches. If you live near it, call (904) 541-9860.
Norman Studios made silent films in Arlington in the 1920s, including race films with African American casts, and it is the only historic film studio still standing in the city. Old Arlington's history is part of why its homes and yards vary so much. To talk about yours, call (904) 541-9860.
Tree Hill began as 40 acres, and the state bought most of it in 1975. The city added 10 more acres in 1998 with a Florida Communities Trust grant, where the old Lone Star Stables stood. The preserve guards an urban wilderness from surrounding development. If you live near Lone Star Road, call (904) 541-9860.
The Shields Mound, dug in part by Clarence Moore in the 1890s, measured about 214 feet across. Moore found a midden and a burial there, and he opened only part of it because the mound was so large. Its remains lie off Fort Caroline Road near Hartsfield Road. Anyone near that stretch can call (904) 541-9860 to ask about older yards.
Frequently Asked Questions
Why does paver sealing cost so much in Arlington?
A quote pays for a full job, and the sealer is one piece of it. Washing, drying, joint sand, labor and the coat all count, and the surface must be dry first. Posted prices land between $1.75 and $3.25 per square foot, so ask for each step in writing. A list of steps makes the total make sense.
Which water-based sealer works for Arlington pavers?
No single product fits every drive. There are two types, water-based and solvent-based, and the old coat decides which can go on. Sealer that is water-based cannot sit on top of a solvent-based coat. Ask the contractor to name the product and keep that name for the next coat, so the next company knows what it is working with.
How long does a paver coat last in Arlington, Florida?
Companies often name two to five years as the span between coats. Sun, tire traffic and shade change the number. A paver that drinks water and darkens, rather than beading it, has a worn-out coat. A dated invoice makes the next reseal easier to plan.
How much does it cost to clean and seal pavers in Arlington?
The Jacksonville range of $1.75 to $3.25 per square foot covers cleaning, sanding and sealing. Your total depends on the area and on the old coat. A failed coat must be stripped first, which costs more. A written quote should show the area, the steps and the finish.
Does street flooding in Arlington change how pavers are sealed?
It changes the timing. After water has stood on pavers, they are washed first and left to dry fully, since sealer needs a dry surface. Bedding sand below can stay damp after rain. A short note about where water stands helps the contractor plan.
How soon will someone reply to an Arlington estimate request?
Expect a reply within a day. The estimate carries no charge, and you owe nothing if you decide against the job. Photos and a rough size get you a first range sooner. A call early in the week helps with scheduling.
Nearby areas we serve
Ready for a Free Estimate in Arlington?
Call (904) 541-9860 and tell us about your pavers.
Free, no obligation